So you’ve played with the Makelangelo‘s generated Gcode and now you want to experiment on your own. Cool! Here’s a simple rectangle to get you started.
Now let’s give some values to these parameters:
A
20
B
40
C
10
D
30
My method is to lift the pen, drive to a corner, put the pen down, and then trace the rectangle. That means going to five points because we have to come back to the start.
And voila! I’ve deliberately done this with the origin away from the center so the numbers are more obvious. I hope you see that in a cartesian system the origin could be anywhere. For example, if it were below and to the left of P4 all the X and Y values would be positive.
The Sixi Calibration Tool helps anyone using a Sixi robot make sure that the robot’s mental and physical states match.
They have to match or else.
If they do not match then the move you expect is not the move you will get. This could very quickly lead to an accident.
Ok, what do we do about it?
There has to be a way to synchronize the mental model and the physical model. The calibration tool is made to fit in one place and attach to the arm in only one way. This forces all the robot joints to move to known angles. Those angles are measured in the mental model in Robot Overlord and then copied to the physical model in the robot’s brain.
Sixi robot now has a URDF description and can be found on the ROS wiki.
ROS (Robot Operating System) was first developed by Willow Garage, a Boston robotics company. Though Willow Garage no longer exists, the ROS has been so successful that it has outlived its creator.
Since ROS is such a popular tool, I hired sachinkumar1235 on Fiverr who built the URDF package. It includes decimated STL files created by Andre.
Programming stepper motors to move together correctly for CNC machining can be a challenge and I’m here to help. To move one motor on it’s own is easy enough. Moving several is not too hard, either. What if all those motors are supposed to move in concert and finish their moves at the same time, perfectly, every time? The solution is today’s topic.
A single stepper motor isn’t too hard. Most stepper motors are driven through a dual H-bridge stepper adapter like the A4988, the TMC2130, or the classic L293D. You, the programmer, set the enable pin (turn on the motor), the direction pin, and then flip the step pin high and low for the desired number of steps. Easy enough…
When it’s time to move two motors, I can (of course) move each the full distance.
I could use an Adafruit Stepper Motor Shield, set the target steps and position, and then say “go”. It will move them both one step at a time. One of the motors will be done first. This is sometimes called the hockey stick.
But what we want is both to arrive at the same time.
Notice that I’m using line drawings to describe these movements. The solution to moving these motors is the same one used to draw lines on a screen – Brenseham’s line algorithm.
Now that I’ve described what the issue is and the name of the solution, Here’s the wikipedia entry on Brenseham’s line algorithm. It has pseudo-code and lots more examples to help you out. If that’s not enough, post to our forums with your questions!
One final note: an especially nice feature of Brenseham’s line algorithm is that it does all the math with whole numbers only, which are much faster to calculate in a microchip AND won’t have any rounding errors that can happen in said microchips. So perfect results every time.
Brenseham’s line algorithm is used in Makelangelo-firmware, Marlin, and probably several other CNC firmwares.
An eccentric cam shaft is at the heart of our cycloid gearbox. Any force acting on the gearbox is focused at this point. So it makes sense that a good gearbox has a super strong cam shaft. This design is made to connect on a motor with a 1/4in diameter shaft, which happens to be the same as the NEMA23 motor in the elbow of the Sixi Robot.
Want to practice your CAD skills? Try making a 3D model of this part, yourself. Tag us on social media if you do!
